CAB Apollo 1 Specifications download pdf (Page 47)

B/27

Tyre pressure table

MISURA PNEUMATICO

TYRES DIMENSIONS

DIMENSION DES PNEUS

DIMENSION DE LOS NEUMATICOS

REIFENMASS

CARATTERISTICHE

DETAILS

CARATTERISTIQUES

CARACTERISTICAS

EIGENSHAFTEN

BAR

12,5 R18 12PR 3,0

12,5 R20 12PR 3,5

18 R19,5 16PR 4,5

16/70 R20 14PR 3,5

18 R22,5 16PR 4,5

405/70R20 (16/70-20) 14PR 3,5

405/70R20 (16/70R20) 152J 6,0

405/70R24 (16/70-24) 14PR 4,0

405/70R24 (16/70R24) 152J 5,0

445/65R22,5 (18R22,5) 169F 8,0

445/65 R22,5 168A8 8,5

14.00 R24

17.5L R24

445/70R24 (17.5LR24)

500/70R24 (19.5LR24)

16PR

151G

164A8

3,75

4,0

4,1

4,0

12,5 R18 10PR 3,0

10,5 R18 10PR 3,75

- Check the size of the tyres installed and the ply number

to ensure they are inﬂated to the correct pressure.

- To ensure maximum efficiency do not use tyres with

more than 80% of tyre tread wear.

- ATTENTION -

Inﬂating or working on tyres can be dangerous.

Whenever possible, have specialised personnel interve-

ne on or install tyres. To prevent serious or mortal inju-

ry, follow the safety precautions described below.

- Vehicle tyres are very heavy. Handle with care and ensu-

re that, once stored, they cannot fall and injure anyone.

- Never attempt to repair a tyre on a public road or motorway.

- Make sure that the car jack is positioned on a solid, ﬂat

surface.

- Make sure that the jack is suitable to support the weight

of the vehicle.

- Use jack tripods or other locking devices suitable for

supporting the vehicle while repairing tyres.

- Never place any part of your body under the vehicle.

- Never start up the vehicle while it is on the jack.

- Never hit a tyre with a rim or hammer.

- Make sure that the rim is clean, and that there is no rust

or damage. Do not weld, braze, repair or use a damaged

rim in any way.

TIGHTENING WHEEL NUTS

- Tighten nuts in accordance with the schedule provided in

the maintenance table

- When tightening the wheel nuts, torque should be as follows:

Wheel stud 18 kgm 50

Wheel stud 22 kgm 60

- Always tighten the nuts positioned opposite each other,

not consecutively.

- After having remounted the wheel, tighten the nuts

between the wheel and axles. Check that nuts are tighte-

ned each day until torque has stablised.

- ATTENTION -

THE NUMBER OF AXLE STUDS MUST CORRESPOND

TO THE NUMBER OF TIGHTENED NUTS.THEREFORE

ALL NUTS MUST BE MOUNTED IN ON EACH TYRE;

OTHERWISE THE VEHICLE WILL NOT OPERATE.

- In the event of tyre replacement, the vehicle or the lif-

ted side can be set back on the ground only with tyres

mounted and properly tightened.

- ATTENTION -

NUT TIGHTENING MUST BE CARRIED OUT FIRST WITH THE

VEHICLE, OR PARTS OF IT, LIFTED FROM THE GROUND,

AND THEN WITH THE VEHICLE ON THE GROUND.

- Only use original DIECI nuts to tighten the wheels.

Should even just a single nut be lost, contact the DIECI

service centre.

TYRES

- ATTENTION -

UPON RECEIPT OF THE VEHICLE,

CHECK TYRE AIR PRESSURE.

- Check tyre pressure every 100 hours and every two we-

eks. Pressure should be checked when the tyres are cold.

- Before each use, verify that the sides of the tyres are not

damaged.

- ATTENTION -

TYRES THAT ARE TORN OR ARE EXCESSIVELY WORN

SHOULD BE REPLACED IMMEDIATELY.

- Keep all oils, grease and corrosive liquids far from the

tyres to prevent any damage to the rubber.

- Tyre pressure must be kept at the level indicated in the

table. The tyre pressure given corresponds to the re-

commendations of the manufacturer, and should there-

fore be respected as far as possible.

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 233 234

Comments to this Manuals

No comments

CAB Apollo 1 Specifications Page 47

Comments to this Manuals

Related products and manuals for Label printers CAB Apollo 1